• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Woodworking Information That You Cannot Work Without

By The Carpenter

Most people don’t know much about the hobby of woodworking. They think it’s just a matter of cutting some wood, slapping it together and calling it a success. The fact is that there is more to it than that, and the tips below will guide you through the process.

If you are trying new skills, make sure that you practice on some wood that has no value, like some scraps. You don’t want to waste an expensive piece of wood before you know exactly what you are doing. Once you have mastered your new skills, you can move to a better piece of wood.

Get to know the general properties of any wood you are buying, especially if you want to stain it later. Wood designated as “paint grade” is lower in quality and not suitable for staining. Also, particleboard and veneer will be a lot more different. Veneer isn’t going to absorb a lot of stain while your particleboard will absorb way too much. The proper wood helps your project come out the way that you hoped.

Know your wood. Every block of wood is unique. Different trees respond differently to staining. The grain patterns of different woods mean pieces splinter differently. Different grains will be found on each. These will be factors when working with wood.

Sometimes a little bit of glue is better than a clamp. Every woodworking shop should have a hot glue gun. Hot glue will hold small pieces better than any clamp ever could, if you could even maneuver one in place. When you are done, just gently pry loose with a putty knife.

Make sure that you are wearing the appropriate protective gear when you are working on your woodworking projects. Your safety is of primary importance. Eye protection can protect your eyes from flying wood debris. A pair of strong gloves can protect your hand from splinters. Make sure that you have these essentials before you start on any projects.

Shop around for used power tools. You should be able to find great deals on good tools when you buy them used. You can save lots of money this way when you are a beginning woodworker.

The most important part of any woodworking project is safety. There are many sharp tools that need to be used and you should be very careful when using them. Find out the proper way to use these tools. If they are power tools, read the manual. If they are hand tools, have a professional show you how to use them properly.

Save time in the shop by locating the most level spot on your floor and marking it with a brightly colored duct tape. When you do this, you can quickly and easily maneuver your mobile table saw into position for board cutting. You will not have to check the level and make time consuming minor adjustments every time you want to cut a board.

Make sure there are no spots of glue on the wood before proceeding to finish your project. The spots will show up as lighter spots after the finish has been applied. You can use mineral spirits of naptha to completely remove all traces of glue from the wood. You may also be able to remove the glue by sanding the wood.

As you learn more about woodworking, you’ll find that things become easier. You’ll be able to plan out your projects better, complete them on time and have end results which are impressive. Use this new knowledge to make your hobby the best it has ever been, time and time again.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com