• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

What One Should Know About Woodworking Before Getting Started

By The Carpenter

It can be tough to run a woodworking business that is successful. Working hard and being dedicated to the craft is a must, but first you need to gain the necessary knowledge on how to run this business. In this article, you will find a lot of helpful tips for your woodworking business. Continue reading and use the suggestions offered to learn as much as you can.

Reusable sanding blocks save you time and money. To make them all you need is a few pieces of scrap lumber. Cut a piece of 2×4 into a rectangle approximately 2 inches wide and 4 inches long. Cut a piece of sandpaper the size of your block. Then, spray one side of the piece of lumber with spray adhesive and adhere the sandpaper to the block of wood.

Take the time to plan out your woodworking project step-by-step before you even begin. Doing this will help to ensure that you are going to get the results that you are looking for. If you do not plan ahead it is likely that you will make an error that could ruin the entire project.

You can use tape to catch excess glue. If you want to prevent oozing glue stains along joints, try clamping pieces together without using any glue. You just put tape on your joint, and then cut along it using a sharp blade. Separate your pieces, and then apply glue. After that, clamp them to each other again. Your glue will ooze on the tape instead of the wood. You can peel off the tape before your glue dries.

When sanding a piece of lumber, beginning with a coarse sandpaper. Remove the excess dust from the lumber. Then, once the largest scratches are removed, sand again with a smoother sandpaper. Follow this sanding with a tack cloth. Continue using smoother sandpaper until the lumber feels smooth when you run your hand across it.

Always wear safety glasses when you are doing anything that involves woodworking. If you do not take the time to put the glasses on you are taking a huge risk that is not sensible. Just think, if you lose your eye sight you will not be able to do woodworking every again.

Before you start any woodworking project, get all of the tools you will need for the project ready. Always remember to bring a calculator and tape measure with you when you go to purchase your wood. Make sure you have any specialty tools you will need for your project available as well.

All woodworking shops should have stair gauges. They are generally used for laying out stair jacks, but they can be used to clamp carpenter’s squares. This can make a carpenter’s square serve as a guide for a circular saw. Using the square, you will have perfectly straight cuts every time.

Remember the quote, “Measure twice, cut once.” When it comes to cutting wood, you always want to ensure you have the right measurements before you begin cutting. Otherwise, you will have to buy more wood, which will cost you a lot of money. You can avoid this dilemma by ensuring proper measurements.

If dust and dirt get into the holes of a brad or nail gun while they are not in use, this can cause them to wear out more quickly. It is a good idea to plug the air inlet holes up with something to prevent anything from getting in there.

As discussed, woodworking requires some work and effort. You need to understand all you can when it comes to woodworking itself as well as business organization. Use the tips laid out here, and use them to further your business in woodworking.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com