• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Want To Learn Woodworking? These Tips Can Help!

By The Carpenter

If you are interested in gaining woodworking know-how, this is the place for you. The tips in this article are useful no matter what your skills. If you’re ready, keep reading for some awesome advice.

Use stop blocks to your advantage for more accurate work. When cutting a lot of pieces the same size, no matter how carefully you measure, you often find small variations. Use a pre-cut stop block to make those measurements pinpoint accurate. Then the table saw will stop at just the right length length.

Always put your safety first when it comes to using tools, stains and paints. The more variety you use, the more specifics there are about applications, tool use, times for drying, and more. Put your safety first by reading the instructions, wearing any necessary protective gear, and working in areas with good ventilation whenever using oil-based products or anything that produces air pollutants.

Before practicing advanced woodworking techniques, make sure you’ve got the basics down. Typically those advanced techniques rely on you knowing the basics like the back of your hand. If you don’t, you’ll more than likely find learning to be a very frustrating experience. So start slow, and work up from there.

Before you start any woodworking project, get all of the tools you will need for the project ready. Always remember to bring a calculator and tape measure with you when you go to purchase your wood. Make sure you have any specialty tools you will need for your project available as well.

Make sure your workbench is the proper height. It really can make a big difference. It needs to fit you and how you work. Usually if you are around 5’6″ to 5’9″ you probably need one that is between 33″ and 36″ high. If you are 5’10” or taller, you may need one that is between 35″ and 37″ high. Use your bench at its current height to determine if you need to change it to work better for you.

Be certain you use the right nail size for any project. If you use a nail whose diameter is too great, it can split the wood, which causes it not have a proper hold. A small nail, however, won’t be able to join the wood together. You must be able to determine the right size for the job.

Always keep your work area clean and safe, even when you are not actually there. Leaving out pieces of lumber with nails in them or even power tools that are easily activated in your yard can be dangerous. You never know when animals or even neighborhood children might come romping through and hurt themselves.

If you mark your intended cuts with pencil lines, try not to actually cut them! You might be lined up at first, but it is possible to get a little off later in the cut, resulting in pieces that fit less that perfectly. It’s better to cut the edge of the pencil line and then sand the rest of the marking off.

You can apply stain with either a brush, or a rag. Work the stain in against the grain, and with it as well. You need not be neat, just get a smooth, even coat on the wood. Then, wipe immediately for a lighter tone, or leave it on for up to fifteen minutes before wiping for a deeper tone.

The article you just read if full of useful tips on how to become a great woodworker. You have some useful information that you can use for your next woodworking project. It’s time to start that project!

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com