• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Want To Learn Woodworking? Check Out These Handy Tips!

By The Carpenter

Woodworking is a skill that many people desire. Woodworking offers something to everyone, beginner and master woodworkers alike. Read on for tips on enhancing your skills and taking your woodworking skills up a notch.

Reusable sanding blocks made by yourself will save money. Make a list of each sandpaper grit that you typically use, and then cut a full six blocks for each from scrap plywood, 3/4″ thick. They should be able two and a half inches by four and three-quarters inches. Use spray adhesive on both the cork tile square and your blocks. If the cork is too large, trim it with a utility knife. Put adhesive on a sheet of sandpaper and apply it on each block of cork. Fnally, make sure you cut sandpaper flush with the cork, and label every block.

TIP! Make sanding blocks that are reusable. To do this, cut six blocks of wood from scrap plywood that is 3/4″ in diameter for each sandpaper grit.

Anytime that you begin a new project you must consider your safety first. Be sure that you use the tools as they’re supposed to be used while you’re wearing safety equipment. Always keep safety guards in place on power tools. You do not want to start a woodworking project and end up in the hospital.

Consider making your own sanding blocks that can be used again and again. Begin by cutting some 3/4 inch plywood into blocks. Be certain the pieces are about two and a half inches by four and three quarter inches. You can secure the sandpaper better with an adhesive. If the cork is too large, trim it with a utility knife. You can then spray adhesive on some sandpaper and place it on the corks. Finally, trim the sandpaper and label each block.

Gel stains are great for staining furniture. Gels stains seem to hold onto the lumber better where liquid stains have the tendency to run when applied. Gel stains are much thicker so they give more consistent coverage.

TIP! Gel stains are something that you can get a lot of use out of when you’re staining items that are going to be used for furniture. Gel stains work better on lumber because the liquid kind usually run.

Before you apply a stain, test it on an area that is hidden or a piece of wood scrap. This makes sure that you won’t run into any surprises. Since wood is often unpredictable, you can avoid unpleasant surprises by completing this test.

It is important that you have a realistic idea of your budget and what you can make with it. Sometimes your eyes are larger than your wallet when you have a particular project in mind. It is important to have all of the items fit in your budget. Create a budget before you start so that this never happens.

Do some dry fitting before applying glue and then piece the wooden pieces together. Adjusting your wood after applying glue can cause damage to your project. Using dry-fit will show you where to put the pieces should go.

TIP! Prior to applying glue, attempt a dry fitting. If you don’t and then try to do adjustments, chances are you’ll create damage to your project.

You need a good stair gauge in your shop. They are used most often for laying out stair jacks, but they can also be used to clamp carpenter squares. You can then use your square as a guide for a circular saw. Using the square, you will have perfectly straight cuts every time.

It’s important to know the wood’s characteristics before you start working with it. Lower quality wood will be called paint grade. Stain grade will be of higher quality and have a nicer finish. Particleboard will take on too much stain, while veneer doesn’t take on enough. Buying the right wood will help make sure your project is a success.

Every shop that does woodworking needs to contain a stair gauge. They are typically used to put down stair jacks, although they can function as a clamp for a carpenter’s square. It can transform your square into a circular saw guide. Using the square can help you get straight cuts each time.

TIP! Every shop that does woodworking needs to contain a stair gauge. They can be used to clamp a carpenter’s square along with laying out stair jacks.

Understand the properties of the wood you’re using. Each wood piece is different. The trees that these woods come from could take the stain differently. Different woods will splinter in unique ways. You will also notice many variations in grains. All of this will become factors in your woodworking project.

Golf Tee

Be aware of the different kinds of characteristics of the wood you are working with, before you choose it for project where staining is involved. You’ll want to look for paint-grade or stain-grade woods, depending on your desires for the project. When it comes to veneer and particle board, veneer doesn’t usually absorb the right amount of stain, and particle board absorbs way too much. Your project will turn out better if you make sure you get the right wood.

TIP! You want to know the different characteristics of the wood you’re going to use, especially before the staining process. Wood that is paint grade is not high quality.

If you have loose interior door hinges to work on, you may be able to just use a golf tee to help. Remove hinges and door from door frame and lightly tap one golf tee inside each of the screw holes. Trim off the end of the tee still sticking out and hang the door again. A golf tee will give the screw a surface in which to adhere to.

It is not a shock that woodworking has been a craft that has been around forever. Since the dawn of time woodworking skills have been in high demand. No matter how important woodworking is to your life, the above tips will make you appreciate it more.

Before using wood, make sure you have a good grasp of all the different types of woods that are out there. Each type of wood has different traits. The trees that these woods come from could take the stain differently. Different cuts of wood will also splinter differently. And, you will notice a plethora of grains. All of this will become factors in your woodworking project.

Filed Under: Woodworking Tips Tagged With: golf tee, woodworking project, woodworking skills

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com