• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Top Woodworking Tips Straight From The Pros

By The Carpenter

Have you ever wanted to take up a hobby like woodworking, but weren’t quite sure how to go about it? If so, this is the article for you. If you are new to working with wood, advice can help to make the job easier. Below, you will find helpful tips to get you started.

TIP! Keep safety in mind at all times. Proper tool use and safety equipment are important when you are woodworking.

Use the right wood for your project. Not all woods are equal. If you don’t know how different types of wood will work, spend time learning about both the wood and the project you wish to complete.

Gel Stains

TIP! Are you aware that your workbench height is essential for having successful woodworking projects? To find the best height, measure the distance from the floor to your waistline. This will help you create a workbench that is the perfect height.

Gel stains are fantastic when you stain furniture. Liquid stains are prone to running, while gel stains tend to stick. Gel stains are much thicker so they give more consistent coverage.

You ought to attempt dry fittings before putting glue on the wood to piece things together properly. If you’re trying to fix things up after you have glue on your piece, there is a chance that you’re going to damage the project. You can figure out what goes where with a dry fit.

TIP! When you’re using any kind of laminate while working with wood a good way to trim your laminate is to use tin snips. This tool is intended to cut metal, so it easily slices through laminates, which greatly reduces the energy needed.

You should check the condition of your blade before you start sawing. A dull blade can’t efficiently get the job done. It can also cause mistakes that are costly, depending on the wood you use.

Do you sometimes find a screw that needs tightening, but is in an awkward place where you can’t reach with the screwdriver and your hand? Do not look past your toolbox for the answer. Grab a 12-point socket and your long-handle screwdriver. Place the socket on your screwdriver, then attach this to a ratchet.

TIP! Every woodworking shop should have a stair gauge in it. This is used for laying out stair jacks and can also be used to clamp a carpenter’s square.

Always pay attention to safety when using a table saw. When executing a crosscut, set the length for the cut by clamping a wooden block to the fence. This is preferable to simply using the fence because it will prevent having your board spring back. By clamping, the board end stays free to be cut.

When sanding, don’t apply too much pressure. Pressure can cause you to get uneven results, or might gauge the surface. Strong force shouldn’t be necessary if you’re using the correct grit of sandpaper. Use a circular motion and sand lightly.

TIP! It’s great to have a small ruler inside your pocket, but it might fall out if you have to bend. A great way to remedy this problem is to purchase a metal ruler, keep this in your pocket with a telescoping magnet that is used to gather up any loose screws.

A stair gauge can also be used to guide a circular saw. Typically, stair gauges are used to calibrate stair jack rises and runs. Having said that, utilizing both on carpenter squares creates excellent circular saw guides.

Wet surfaces before sanding them. This helps raise the grain. This will then allow you to get rid of fine scratches. As a result, your project will look much better when it is finished. It saves you work in the future as well.

TIP! Be certain you use the right nail size for any project. Nails that are too large can cause the wood to split.

It’s not easy to work with wood, but the rewards are endless. The pride you get when you see that you have finished a piece can be a feeling that you treasure for months. Keep the advice you’ve learned here in mind as you get started with woodworking.

Filed Under: Woodworking Tips Tagged With: gel stains

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com