• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Top Woodworking Tips Straight From The Experts

By The Carpenter

Woodworking sounds like such a simple activity, but it is one with many intricacies. If you think you already know everything about it, think again. There is always more to learn. The article below will show you what you need to know about woodworking. Both novices and experts will find this information very useful.

You can make reusable sanding blocks. Cut six 3/4″ pieces of plywood for each sandpaper grit. Cut them to 2.5″ by 4.75″. Spray some adhesive on your blocks and on the cork tile. Stick a single block onto the cork and make sure you’re cutting the cork in a flush way using your utility knife. Get a sandpaper sheet, spray it with adhesive, and then apply it to each of your cork blocks; they need to be face down. Finally you can cut the sandpaper so it’s flush with the cork and then you can label each block.

The reason why many power tools have guards on them is to keep you safe. Never remove the guards off of any of your tools. You may not understand why they are there, but they are there for a reason. They are there to protect you from sharp blades, moving parts and other things that could potentially hurt you.

Using a good wood glue can make joined pieces even stronger than the wood itself. The key to strength in a glued joint is the amount of time the glue takes to set. Glue that takes longer to cure is better than quick setting glue. Slower setting glue has more time to penetrate into the fibers of the wood, which enhances the strength of the joint.

If you will be re-coating an existing finish, be sure that the surface is clean and free of any wax or oils. Then, let it dry completely, and lightly scuff the surface with a 220-grit sandpaper so that the finish you are applying will have something to hold onto.

Never skip sanding when it is necessary or think that staining hides imperfections in the wood. Wood with scratches, dents and nicks absorbs much more finish or stain than wood that is smooth. When you skip sanding or do not do a thorough job of it, the imperfections stand out even more because of the increased absorption.

If there is a joint in your work that does not fit together properly, this cannot be fixed with glue. While it may seem like the simple way to fix things, it will only work temporarily. The best thing to do would be to start over and be more careful the next time.

Did you know that the teeth on a hacksaw face forward? Many people do not know this. It is the opposite of a wood saw. These saws are supposed to cut when pushed forward. Many times the blades are not labeled for correct installation. If this is the case, remember to put the teeth facing forward.

If you plan on applying any gloss or stain to a piece of wood, it is very important that you sand it down first. Failing to do this step will result in a wood surface that is not very smooth. Use sandpaper to smooth things down then make sure all dust s removed by brushing it with a cloth.

Now that you’ve come to the end of this article, you know a thing or two more about woodworking. Use the information for fun or profit as you see fit. Keep learning more and honing your skills along the way. It is entirely possible that you will become one of the world’s great woodworkers.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com