• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Top Woodworking Tips Straight From The Experts

By The Carpenter

Woodworking is a skill high in demand. There are many techniques to learn when it comes to woodworking. Below you will find tips from the experts that will enable you to increase your woodworking skills.

Clean your saw’s teeth before cutting lumber. To thoroughly clean your saw blade dip a shop rag into a little acetone and wipe the blade thoroughly. Additionally, using a piece of sandpaper that has a fine grit will remove any sap or gumminess from your skill saw’s cutting blades.

Take your time when using an electrical saw to cut your wood. If you are doing a woodworking project and try to do it quickly you are risking injury as well as are more likely to make a mistake. Be sure to not even try to start something if you do not have plenty of time.

Visualize your woodworking project from start to finish before taking any tool to the wood. Let your brain and imagination help you get used to what you’re about to do. In fact, when you visualize, you’ll be much less likely to make costly mistakes during the middle of a project.

Glue can cause nasty stains on your finished work. You can eliminate stains easily using a piece of tape. First, clamp your wood together without any glue. Put a piece of tape over the joint. Cut the tape on the joint with a sharp knife. You can now clamp the wood together with glue and any excess will ooze onto the tape, not the wood.

Did you know that the teeth on a hacksaw face forward? Many people do not know this. It is the opposite of a wood saw. These saws are supposed to cut when pushed forward. Many times the blades are not labeled for correct installation. If this is the case, remember to put the teeth facing forward.

When buying wood for your woodworking project, always buy long and not to the exact measurements. Some stores will sell you wood that is cut to length. Always measure long and trim down to the exact size you need in your shop. This way if you made a minor error in measurement, you will have a little bit of extra wood to cut off or utilize to make up for the difference.

Before even beginning a woodworking project, make sure you have an adequate and proper place to work in. You definitely don’t want your living space filled with sawdust. Some woodworking supplies, such as stains, varnish and paint strippers, have noxious fumes. Ideally, you will have a detached garage or a shed to work in since an outside space is an ideal location.

Always check your tools before you begin using them. Woodworking with a faulty or overused tool can easily lead to a serious injury or destruction of your materials. To make sure that this does not happen to you take the time to thoroughly inspect your tools from top to bottom.

Never allow someone to watch while you are woodworking without wearing the same gear that you are wearing. Being anywhere near the tools is a hazard, even if they are not using them. Wood or parts of the tool could fly into the air and strike them just as they could you.

It is no surprise that woodworking is a skill and a hobby that has stood the test of time. There will always be some kind of a project out there for a gifted woodworking professional to work on. Regardless of your level of involvement in woodworking, the tips included here should help you.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com