• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Tips And Tricks About Working With Wood

By The Carpenter

When it comes to woodworking, there is a vast world to learn about. From types of wood to which tools are best, you will find that there is no end to your education. To learn some more about your favorite pastime, this article provides you with helpful hints to help you be more successful.

Take the time to plan out your woodworking project step-by-step before you even begin. Doing this will help to ensure that you are going to get the results that you are looking for. If you do not plan ahead it is likely that you will make an error that could ruin the entire project.

When you are working on a project, be sure to face your light directly on your working area. The bright light will enable you to detect any drips or runs you may not see otherwise. Missed areas will also be more visible. Be sure to always work in a well-ventilated area as well.

Ask local hardware stores if they sponsor woodworking classes. You may be surprised by what you find! In fact, your local Home Depot or Lowes might have classes available monthly that’ll help you hone your skills. This is a quick way to grow as a woodworker with very little out of pocket costs.

When you find a nice level spot on your workshop floor for your table saw, it can be difficult finding the same spot after you put your saw away. When you do find a level spot, use duct tape on the floor so you know where to position your table saw next time you need it.

Learn how to find the center in a piece of firewood every time. Mount some flat scrap wood to the lathe’s faceplate. Attach an acrylic piece to it using some double-faced tape. Chuck that in your lathe. Turn your acrylic to a disc. Using a 1/16″ bit in your tail stock chuck, drill a hole through that center-point. Scribe some concentric circles on to the disc at 1/2″³ intervals using a skew chisel. Position this center-finder over the end of your stock and adjust it until one of your circles is inscribed completely in a portion of the wood that is solid and usable. Using an awl or nail set, mark your center through the central hole in the disc.

Learn about using pilot holes. This is pretty simple to do. When driving a screw or hammering a nail into a little piece of wood or getting pretty close to the edge of a piece, it tends to split. Sometimes it’s unavoidable to put a fixing into a place like this. However, drilling a hole through the joint that’s a bit smaller than the fixing can prevent it from splitting.

Always check your tools before you begin using them. Woodworking with a faulty or overused tool can easily lead to a serious injury or destruction of your materials. To make sure that this does not happen to you take the time to thoroughly inspect your tools from top to bottom.

Make sure you buy the right tool for the job. When you are building a wooden deck onto your house, it would be difficult to do all the cutting with a hand saw. Instead, you should cut with a circular saw. A circular saw is electric; however, a hand saw is not.

Whether you prefer to do it in your spare time or enjoy it as your career, woodworking is truly an enjoyable thing for you to do. That is why you found this article and have gained the knowledge you absorbed today. Take that new data and start using it as soon as possible.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com