• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Tips And Tricks About Working With Wood

By The Carpenter

The world of woodworking ranges from creating benches to bridges and everything in between. That means there is a huge cache of knowledge out there just waiting for you to tap into it. Take your time and read this article in full to learn some new tips and tricks.

Practice some table saw safety. When crosscutting with a table saw, set your cut length with the block clamped to your fence. Do not use your fence directly for avoiding get kicked back by a board directly. You need to clamp the block of wood to your fence before your blade. The board’s end is free of the fence when you cut and after you cut.

When using stain, try a test on a small scrap you may have available or in an area on the wood that will be out of sight. If you test the stain color first, you will not have any unpleasant surprises. Wood can be unpredictable, so you can avoid mistakes and disappointment by doing this simple test.

Stair gauges make good crosscut guides. To use, clamp the gauges to a carpenter square. Then mark the notches. Have the share one tongue of the carpenter square. This is a combination that will provide you and excellent crosscut guide for your circular saw.

Use hot glue instead of clamps for little things. When cutting, filing, sanding, or finishing something small, use the hot glue gun to glue the piece to your pedestal stick. The glue holds holds just like clamps, if not better than clamps. It also works great for things that clamps will not work on. When you finish your project, loosen it gently with a putty knife.

When you install your hacksaw blade, make sure the teeth face forward. They are designed to cut when pushed using a forward stroke instead of a pulled stroke. Some of these blades have arrows pointing toward the handles that show the correct way to install them. Install it making sure it is tight and cannot bend. When you do lots of cutting, your blade heats up and expands, so make sure you tighten it before it begins bending.

When you want to cut narrower sections of wood, never use your own fingers to guide them. Rather, make use of a longer, thinner piece of wood that can push it along the saw’s surface. This will assure you keep your fingers.

If you find that there is rust on any of your woodworking tools there is a rather easy solution. As long as the rust is just on surface, all you need to do is use a pumice stone on the spot. Be sure to scrub gently, as being too rough can lead to you damaging the tool itself.

If you mark your intended cuts with pencil lines, try not to actually cut them! You might be lined up at first, but it is possible to get a little off later in the cut, resulting in pieces that fit less that perfectly. It’s better to cut the edge of the pencil line and then sand the rest of the marking off.

Never allow someone to watch while you are woodworking without wearing the same gear that you are wearing. Being anywhere near the tools is a hazard, even if they are not using them. Wood or parts of the tool could fly into the air and strike them just as they could you.

Whatever you do when it comes to woodworking, it is important that you take the time necessary to learn as much as you can. Read articles written by experts, like this one, and learn from your peers. The more you know, the better your projects will end up once done.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com