• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Simple Tips And Tricks About Working With Wood

By The Carpenter

Woodworking is one of the things that separates man from the rest of the animal kingdom. Few other species demonstrate the ability to take wood and use it to create something. When you work with wood, you have the power to visualize something in your mind and then create it into a physical reality. The following paragraphs are full of tips on how to make this easier.

Try using a stair gauge as a crosscut guide. Match them to the rise and run of your stair jack, then attach them to the carpenter’s square. Mark each notch. You will make a crosscut guide for your circular saw when you put it on the carpenter’s square.

If you will be re-coating an existing finish, be sure that the surface is clean and free of any wax or oils. Then, let it dry completely, and lightly scuff the surface with a 220-grit sandpaper so that the finish you are applying will have something to hold onto.

Before you start any woodworking project, get all of the tools you will need for the project ready. Always remember to bring a calculator and tape measure with you when you go to purchase your wood. Make sure you have any specialty tools you will need for your project available as well.

When working with wood, it is important that you have a lot of patience when it comes to the finishing process. This is just as important as the actual woodworking. Things like gluing edges and sanding the wood down take time, and you will only mess things up if you try to rush through this process.

Visualize your woodworking project from start to finish before taking any tool to the wood. Let your brain and imagination help you get used to what you’re about to do. In fact, when you visualize, you’ll be much less likely to make costly mistakes during the middle of a project.

Remember the quote, “Measure twice, cut once.” When it comes to cutting wood, you always want to ensure you have the right measurements before you begin cutting. Otherwise, you will have to buy more wood, which will cost you a lot of money. You can avoid this dilemma by ensuring proper measurements.

If you find that there is rust on any of your woodworking tools there is a rather easy solution. As long as the rust is just on surface, all you need to do is use a pumice stone on the spot. Be sure to scrub gently, as being too rough can lead to you damaging the tool itself.

Did you know that the teeth on a hacksaw face forward? Many people do not know this. It is the opposite of a wood saw. These saws are supposed to cut when pushed forward. Many times the blades are not labeled for correct installation. If this is the case, remember to put the teeth facing forward.

Woodworking can be expensive. It is a good idea to go over your plans before you start and make sure that the project fits within your budget. Price out all materials by making a list of the required supplies and then go to the local hardware store to figure out the total cost.

As stated in the introduction, there are scant few species that do woodworking of any kind. One of the facets of the human race that makes us distinct from lower forms of life is our ability to have a mental idea and make it a physical reality with wood. Use the ideas within this article to make woodworking one of your better personal skills.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com