• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Simple Steps To Help You Better Understand Woodworking

By The Carpenter

Working with wood lets you allow your art out. It’s a popular and rewarding experience. Wouldn’t you like to learn all you can? Read on below, as there’s lots you will discover.

You can make your own reusable sanding blocks. Start by cutting six blocks from scrap 3/4″ plywood for every sandpaper grit you generally use. They should be 2.5″ by 4.75″. Put adhesive spray on the blocks and your cork tile square. Trim the cork so that it is flush around the edges of the block. Put adhesive on the sandpaper sheet and then apply it to the cork blocks face down. Use a utility knife to trim the sandpaper around the edge of the block. Label each block.

TIP! Consider making your own sanding blocks that are reusable. Cut six blocks from some plywood that you have laying around for every piece of sandpaper that you use.

You can make reusable sanding blocks. Start by cutting a few blocks from a scrap piece of plywood for all the sandpaper grits you need to use. Be sure that they’re only around 2.5″ x 4.75″. Use a spray glue on the blocks and the tile square. Stick a block to the cork, making sure to cut the cork flush with a utility knife. This piece should then fit you hand fairly well and be secure enough to not slip. Cut the sandpaper flush and label the block.

Did you realize that how high your workbench sits will have an effect on your work? To find the perfect height of your workbench measure the distance between the midline of your waist and the floor. This is the perfect workbench height.

A great tool for setting crosscut guides is a stair gauge. Clamp them to your carpenter’s square, and make sure they match your stair jack’s rise and run. Next, mark your notches using the guide you have set. If you place the on the tongue that’s on your carpenter’s square, this means that together you can use this as a good crosscut guide for the circular saw.

TIP! Stair gauges can be used for crosscut guides. Clamp them on the carpenter’s square.

When you’re working out a budget, you have to think about itemizing the new tools you may have to purchase. It is easy to miss the extra expense when you are too busy thinking about the cost of the wood. But, if you need other things that you don’t own and didn’t think about, you can really mess up your budget and may not be able to finish your project.

Never guide wood through a table saw with your fingers. Rather, make use of a longer, thinner piece of wood that can push it along the saw’s surface. This will help ensure you keep all of your fingers, making woodworking much easier.

Gel stains are the new big thing for staining furniture and other wood projects that need staining. Gel stains will adhere much better to your wood. Not only that, but gel stains tend to be thicker than liquid, so that the pigment is consistent, which makes for a more even stain on vertical and horizontal pieces.

TIP! Gel stains are an excellent choice for furniture staining. Liquid tends to run after it’s put on, whereas a gel stain sticks to the wood much better.

Use tin snips if you are working with laminate. This tool is intended to cut metal, so it easily slices through laminates, which greatly reduces the energy needed. Try designating a pair of snips for laminate cutting so that they stay sharp.

Golf Tee

Do not use your fingers to guide a narrow strip of wood into the saw. Instead, use a piece of scrap wood to safely push the lumber through your table saw. This will help to keep you from cutting off your fingers, which would be a travesty.

TIP! Whenever you’re thinking of cutting a piece of wood that’s narrow, don’t try to use your fingers to guide it. Try using thin wood strips to push that piece through your saw.

You can use a golf tee to help tighten up the hinges of an interior door. Take the door off and remove the hinges, then lightly tap the golf tee into the screw holes. Then, cut the golf tee’s excess off and reinstall the door. A golf tee will give the screw a surface in which to adhere to.

Always use the recommended size nail for your job. Any nail that is way too big in its diameter will split your wood a lot of the time and that makes it not hold right. But if you use a nail too small, it may not have the strength or size to hold the pieces together. Therefore, it is vital that you find the appropiate size nail for your project.

It is handy to carry a small pocket ruler, but it may fall out whenever you bend over. Buy a metal ruler, and try keeping it in the same pocket as the smaller telescoping magnet you use to pick up loose metal screws. The magnet will ensure that the ruler won’t fall out.

TIP! While you might like keeping a small ruler handy in your pocket, you probably find that it falls out every time you bend over. A great way to remedy this problem is to purchase a metal ruler, keep this in your pocket with a telescoping magnet that is used to gather up any loose screws.

Always listen for family and friends that wish to sell their houses. You can earn some extra money by using your skills to increase their house’s resale value. You can do many things to help, such as making new bathroom cabinets or repairing the sagging front porch.

To be able to complete a woodworking project you will need a variety of hand tools. A hammer ought to be the first tool. In particular, a claw hammer should work well for what you want to do. When choosing a hammer, opt for a hammer that feels comfortable in your hand. Avoid purchasing a hammer that’s too heavy.

You should have a good understanding of the different types of wood available to you and their many characteristics. Each kind has different qualities. All the trees react differently to the stains. The grain patterns of different woods mean pieces splinter differently. Different grains will be found on each. This is all important as you embark on your next woodworking project.

TIP! You should have at least a working knowledge about the most common woods and their characteristics. Each kind has different qualities.

It is very thrilling to learn about woodworking, which is a true art. Having a hobby like this is enjoyable. So, get out there and use what you have just learned so that you can create some great art to share with others. You may be surprised with what the product looks like when you’re done.

Filed Under: Woodworking Tips Tagged With: golf tee, size nail

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com