• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Simple Steps To Help You Better Understand Woodworking

By The Carpenter

Have you been searching online for woodworking tips that are simple, yet informative? If so you have found the perfect article for you. Below you will find exactly what you have been looking for and more. Keep reading for the type of advice that you never thought you would be able to find.

Reusable sanding blocks save you time and money. To make them all you need is a few pieces of scrap lumber. Cut a piece of 2×4 into a rectangle approximately 2 inches wide and 4 inches long. Cut a piece of sandpaper the size of your block. Then, spray one side of the piece of lumber with spray adhesive and adhere the sandpaper to the block of wood.

If you will be re-coating an existing finish, be sure that the surface is clean and free of any wax or oils. Then, let it dry completely, and lightly scuff the surface with a 220-grit sandpaper so that the finish you are applying will have something to hold onto.

When you install your hacksaw blade, make sure the teeth face forward. They are designed to cut when pushed using a forward stroke instead of a pulled stroke. Some of these blades have arrows pointing toward the handles that show the correct way to install them. Install it making sure it is tight and cannot bend. When you do lots of cutting, your blade heats up and expands, so make sure you tighten it before it begins bending.

Whenever you work with power tools, be sure your clothing is tucked in properly. Any loose clothing or long, dangling hair or jewelry can easily become tangled in the tool, leading to injury or other disaster. Tuck everything in, pull back your hair, take off dangling jewelry and then get down to work.

Test the color of a stain before doing the complete stain on more visible areas. Wood is never predictable, so a stain may not look the way you expect or need it to when applied to the wood you are using. When you test the stain in a spot that’s not easily visible, you prevent having a project turn out badly.

If you are cutting, sanding, or finishing something small, get out your hot glue gun. Affix the item you are working on to the end of a pedestal stick. Hot glue holds better than a clamp, and small objects are impossible to clamp anyway. Just be careful when pulling the piece off to avoid tearing the back side of the wood.

Add a bit of extra spring in your grip. Sometimes you might need a spring clamp, however you only have one hand available to use. It is sometimes hard to get these things open when you’re only using a single hand. There is a method for making things a bit simpler. While you have two free hands, first get all your clamps ready to go on an available wood wrap. This will make it easy to use them with one hand.

If you find that there is rust on any of your woodworking tools there is a rather easy solution. As long as the rust is just on surface, all you need to do is use a pumice stone on the spot. Be sure to scrub gently, as being too rough can lead to you damaging the tool itself.

Now that you have read the above article you know that you certainly did find the article that you had been searching for. Now the key is to keep these tips in mind so that you can put them to use when you need them. If you doubt you can, you should save this page so that you can refer to them at anytime.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com