• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Seeking Knowledge About Woodworking? You Need To Read This Article!

By The Carpenter

Have you admired a beautiful piece of furniture and dreamed of creating such an item yourself? Do you have a need for a new shelf and want to build it on your own? Regardless of why you want to get involved in woodworking, the advice below will help you get your start.

Create sanding blocks you can reuse. Start by cutting a few blocks from a scrap piece of plywood for all the sandpaper grits you need to use. Be certain they measure 2.5 inches across by 4.75 inches long. Put adhesive spray on the blocks and your cork tile square. Stick a block on your cork, then make certain you cut the cork flush with a utility knife. Spray the back of a sheet of sandpaper with adhesive and adhere the cork side of the block to it. Cut the sandpaper flush and label the block.

Use hot glue instead of clamps for little things. When cutting, filing, sanding, or finishing something small, use the hot glue gun to glue the piece to your pedestal stick. The glue holds holds just like clamps, if not better than clamps. It also works great for things that clamps will not work on. When you finish your project, loosen it gently with a putty knife.

When learning a new woodworking technique, practice it over and over again. Repetition is the best way to learn these skills. So find some cheap wood (scrap wood works), and go at it for some time to hone your skills. This will make it so you’re less likely to make mistakes during important projects.

Glue can cause nasty stains on your finished work. You can eliminate stains easily using a piece of tape. First, clamp your wood together without any glue. Put a piece of tape over the joint. Cut the tape on the joint with a sharp knife. You can now clamp the wood together with glue and any excess will ooze onto the tape, not the wood.

Always remember the rule of measuring twice and cutting once. You are human, which means that mistakes are inevitable. However, you can prevent measurement mistakes from turning into cutting mistakes when you measure two or three times. That is going to spare you serious waste, not just in terms of wasted wood, but also money and time.

You can apply stain with either a brush, or a rag. Work the stain in against the grain, and with it as well. You need not be neat, just get a smooth, even coat on the wood. Then, wipe immediately for a lighter tone, or leave it on for up to fifteen minutes before wiping for a deeper tone.

Always pay attention to safety when using a table saw. While crosscutting, it is important that you use a block properly secured on the fence when establishing the cut length. This will prevent any movement from your board when you are cutting. Using this method keeps the end of the board free for cutting.

Recycle wood when you can. You can also look for good wood to reuse from establishments that have a lot of scraps, like construction or flooring companies. You not just saving a lot of trees when you use recycled wood in your projects. You are also saving some cash.

To get off on the right foot, use these tips as you plan out your next project. That will allow you to use the right techniques to ensure your end result is on target. Once you get that project under your belt, you’ll be able to complete others and truly enjoy woodworking as a hobby.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com