• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

No Time To Research About Woodworking? Just Read This Article

By The Carpenter

Have you thought about taking up woodworking but weren’t sure how? This article is just for you. Woodworking might seem like a tricky hobby, however with the right advice it can be easy. These tips will help.

Use pre-stain conditioners if you’re going to stain the wood. Pre-stain conditioner can help lessen how noticeable blotches and irregularities are when the project is done. These conditioners are going to help smooth out the wood so that the stain can get into it more evenly.

TIP! It is always a good idea to have a pre-stain conditioner for the wood you’re planning to stain. This will help you to get an even finish when you stain.

Create sanding blocks you can reuse. Start by cutting a few blocks from a scrap piece of plywood for all the sandpaper grits you need to use. Be sure that the measurements are around two-and-a-half inches by four-and-three-quarters inches. Spray some adhesive on your blocks and on the cork tile. Put one block on the cork, and then cut it flush with a knife. Put adhesive on a sheet of sandpaper and apply it on each block of cork. You can make smaller blocks if you wish as well. These can be used for smaller pieces demanding finer sanding.

Carpenter Square

You can make your own reusable sanding blocks. To do this, cut six blocks of wood from scrap plywood that is 3/4″ in diameter for each sandpaper grit. Each block should be about 2 inches by 4 inches. Use some spray adhesive on your blocks and the cork tile. Stick a block on your cork, then make certain you cut the cork flush with a utility knife. Then, spray your sandpaper with adhesive and apply it to the cork. Lastly, cut the sandpaper to be flush with the cork. Finish by labeling each block.

TIP! Make your own reusable sanding blocks. First cut 6 blocks from scrap plywood, one for each grit of sandpaper you like to use.

Stair gauges are very important devices for you to use. To use, clamp the gauges to a carpenter square. Then you should mark all of the notches. If you place them on the tongue you’re using for your carpenter square, that combo is a good crosscut guide for your circular saw.

Ask for a how-to demonstration when you rent a new tool. They usually have specialists that could help you adjust to your new equipment a lot faster than you would if you had to do it alone. Find out if they have any helpful handouts or worksheets you can use.

When creating crosscut guides, use a stair gauge. Clamp them to the carpenter’s square, then ensure that they match up with the jack’s run and rise. Then mark the notches. If you place them on the tongue you’re using for your carpenter square, that combo is a good crosscut guide for your circular saw.

TIP! Stair gauges can be used as crosscut guides. Just clamp them on your carpenter’s square while making sure they match up.

A stair gauge is an essential item in every wood shop. They are typically used for laying out stair jacks, but can also prove useful for clamping a carpenters square. You can then use your square as a guide for a circular saw. You can always make perfectly straight cuts by using this method.

Know your wood’s properties before you use it. Paint grade always indicates that the wood isn’t a good quality, for instance, and stain grade will mean the grain pattern will be good for staining. Similarly, veneer and particle board are quite different; the former does not absorb stain well while the latter absorbs too much. Getting the correct kind of wood will help you be sure that you can expect good results.

Use tin snips to cut laminate that you are using for your projects. These snips make it simple to trim down the laminate to a perfect size. Buying tin snips meant to be used just for this purpose can keep them at the desired sharpness.

Golf Tee

If the hinges to your interior door are loose, use a golf tee to fix the problem. Start by removing the door from the frame. Remove the hinges too and tap tees into the screw holes. Cut the extra golf tee off and install the door again. The golf tee fills the hole and provides additional material to hold the screw.

Your woodworking shop needs a stair gauge. They can layout stair jacks as well as clamp carpenter’s squares. You can then use your square as a guide for a circular saw. Every cut you make will be straight when you use the square to guide you.

TIP! Stair gauges are a crucial part of any woodworking shop. They can layout stair jacks as well as clamp carpenter’s squares.

Are you finding it hard to be able to reach a screw that you need to tighten? Look to your toolbox. Grab a screwdriver with a long handle and a 12-point socket. Place the socket on the screwdriver, and then attach it onto your best ratchet.

Go on the search for recycled wood. You can check at places that discard a lot of wood. Commercial shops may just throw good pieces away. Some places include big box stores, other woodworkers and floor shops. Use this to your advantage to find great pieces of wood to use. You can save money this way.

It’s great to have a small ruler inside your pocket, but it might fall out if you have to bend. To reduce this problem, you could get a metal ruler and put the ruler in the same place as where you store your magnet. Keep the ruler and the magnet in the same pocket. The ruler will stay in place.

TIP! Keeping a small ruler inside one of your pockets is a great idea, but it could fall out due to its size. To reduce this problem, you could get a metal ruler and put the ruler in the same place as where you store your magnet.

Woodworking can be a challenge at times, but it can also give you huge rewards. The pride that comes from seeing your finished pieces is worth its weight in gold. Apply the guidance from this piece and make your own works of art.

Filed Under: Woodworking Tips Tagged With: carpenter square, golf tee

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com