• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Learn All About Woodworking With This Article.

By The Carpenter

You might be one of those people who thought they weren’t good with their hands. However, if you take the time to give it a try, woodworking can show you how magical your hands can be. With just the right tips, outlined below, you’re going to be able to make all kinds of pieces. Keep reading!

Familiarize yourself with the tools that you are going to use. This is a very important tip for the beginner, but even more advanced woodworkers can benefit from it too. Lay out the tools and make sure that you know the workings of each one. If you’ve got a brand new tool to you, spend the time that you need with it.

When sanding a piece of lumber, beginning with a coarse sandpaper. Remove the excess dust from the lumber. Then, once the largest scratches are removed, sand again with a smoother sandpaper. Follow this sanding with a tack cloth. Continue using smoother sandpaper until the lumber feels smooth when you run your hand across it.

Your woodworking shop needs a stair gauge. This is used for laying out stair jacks and can also be used to clamp a carpenter’s square. That means your square becomes a circular saw guide. Using the square can help you get straight cuts each time.

Do you lose drill press key chucks often? A good way to keep them within reach is to drill a hole somewhere on the drill press they fit. On top of the press is a good place, where you can see it. Drill a small hole the exact same size of the chuck’s crossbar and it will fit in perfectly.

When working with wood, consider the grade of wood you are using. Wood can be costly and it is not always necessary to use a high-cost wood. If budget is a concern, look at the durability and strength of different woods that may come in a little cheaper and still work for your project.

Only cut using sharp tools. Older and dull tools result in tear-outs and even chipping, which is frustrating and a waste of time. Sharp tools means you get clean cuts quickly. You’ll also spend a lot less time sanding things to get just the right look and fit that you need.

If you are working on your projects in your garage, keep your garage door open. You will be created a lot of wood dust. An open garage door allows your work area to be properly ventilated. Also, during the day, you work area will be better lighted with the garage door opened.

You make mistakes. Always remember that, but never say it. You have made mistakes in the past, you are going to make them in the future. Always treat them as learning opportunities. However, never point them out to others or talk about them. Others may not notice, or even care. They’re likely to just be impressed you did something they couldn’t.

For a beginner, sometimes it is best to buy kits instead of cutting the entire project yourself. You should be able to finish your project quicker with a precut kit. These kits will help you gain some valuable insight on the steps involved in a project so that the next time you can do it all yourself.

You may think that you can’t be an expert at woodworking, but if you stay interested and learn as much as you can, your expert status is all but guaranteed. Just take it slowly and use everything you have learned here to make great-looking wood pieces that you can show off to everyone. Good luck!

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com