• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Interested In Woodworking? These Tips Can Get You Started!

By The Carpenter

Have you been searching online for woodworking tips that are simple, yet informative? If so you have found the perfect article for you. Below you will find exactly what you have been looking for and more. Keep reading for the type of advice that you never thought you would be able to find.

The height of the work bench you use affects the quality of your finished product. Measure where your waist is from the floor. This lets you know what the best height is for your workbench.

Stir finishes or stains before using them. Some of the ingredients tend to settle as time goes on. Shaking can cause bubbling and prevent it from mixing well. Stir until everything is dispersed smoothly and evenly.

In a pinch, you can use a hacksaw blade as a makeshift compass. Often you can’t find a compass when you need it in room, when you are away from your shop. You can quickly nail a hole in the middle of a hacksaw blade, then steady the pencil against the proper tooth to get the right length. Draw that circle.

When you install your hacksaw blade, make sure the teeth face forward. They are designed to cut when pushed using a forward stroke instead of a pulled stroke. Some of these blades have arrows pointing toward the handles that show the correct way to install them. Install it making sure it is tight and cannot bend. When you do lots of cutting, your blade heats up and expands, so make sure you tighten it before it begins bending.

Before you cut into a piece of wood, you need to inspect it to make sure there are not any pieces of metal in the wood. Screws, nails, staples and other metallic object will not only damage your blades, but also pose a safety hazard. Always inspect the wood before you cut.

Choose correctly-sized nails. A large nail can split wood, leaving it loose. But if you use a nail too small, it may not have the strength or size to hold the pieces together. You should know what size you need to get the job done.

Do you find that your joint compound seems to dry out in between uses? There is a simple fix to help keep your joint compound moist. Simply pour a small amount of water on top of your joint compound before sealing it. The next time you need to use the joint compound, drain off the excess water and your joint compound will be perfectly moist.

Never allow someone to watch while you are woodworking without wearing the same gear that you are wearing. Being anywhere near the tools is a hazard, even if they are not using them. Wood or parts of the tool could fly into the air and strike them just as they could you.

Sanding blocks are essential woodworking tools. You can create easy to reuse sanding blocks of your very own by simply cutting three-quarter-inch scrap lumber into rectangles measuring 4.75 x 4.50 inches. Cut pieces of cork tile to fit each block. Spray both the rectangle of wood and the rectangle of cork tile with adhesive and press them together. Allow to dry, then spray the backside of an entire sheet of sandpaper with adhesive. Place your newly made block on the sandpaper with the cork on the down-side. Allow to dry and then use a utility knife to cut the sandpaper around each block.

Now that you have read the above article you know that you certainly did find the article that you had been searching for. Now the key is to keep these tips in mind so that you can put them to use when you need them. If you doubt you can, you should save this page so that you can refer to them at anytime.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com