• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Get Better At Woodworking With These Great Tips!

By The Carpenter

Woodworking can be very enjoyable. However, you may not know how to begin this exciting hobby. Rather than concerning yourself with this, go slowly in the beginning. This article can help you accomplish that.

The reason why many power tools have guards on them is to keep you safe. Never remove the guards off of any of your tools. You may not understand why they are there, but they are there for a reason. They are there to protect you from sharp blades, moving parts and other things that could potentially hurt you.

Before using any new tool, do your research on it in full. New tools can mean serious injuries for those that use them incorrectly. Even if you’re pretty sure of how to use it, don’t risk it. Study up via the web and books related to the tool in question.

Begin small with woodworking projects. It can be very exciting to get yourself ready for your first woodworking project, but don’t let your excitement overtake your smarts. Buy only what you need, no more for right now. Don’t fall for buying tools that you currently don’t need as you may find better alternatives in the future.

Try using duct tape to create a level spot. If you’ve used your table saw on a base that’s mobile, you should be able to easily pull it in and out. To really finish it up, find a level spot on your floor. This also helps you saw boards without obstruction. Mark your wheel positions using duct tape that is brightly colored, and then roll the saw to that same flat spot each time you need to saw.

Learn how to find the center in a piece of firewood every time. Mount some flat scrap wood to the lathe’s faceplate. Attach an acrylic piece to it using some double-faced tape. Chuck that in your lathe. Turn your acrylic to a disc. Using a 1/16″ bit in your tail stock chuck, drill a hole through that center-point. Scribe some concentric circles on to the disc at 1/2″³ intervals using a skew chisel. Position this center-finder over the end of your stock and adjust it until one of your circles is inscribed completely in a portion of the wood that is solid and usable. Using an awl or nail set, mark your center through the central hole in the disc.

Always check your tools before you begin using them. Woodworking with a faulty or overused tool can easily lead to a serious injury or destruction of your materials. To make sure that this does not happen to you take the time to thoroughly inspect your tools from top to bottom.

If you mark your intended cuts with pencil lines, try not to actually cut them! You might be lined up at first, but it is possible to get a little off later in the cut, resulting in pieces that fit less that perfectly. It’s better to cut the edge of the pencil line and then sand the rest of the marking off.

You make mistakes. Always remember that, but never say it. You have made mistakes in the past, you are going to make them in the future. Always treat them as learning opportunities. However, never point them out to others or talk about them. Others may not notice, or even care. They’re likely to just be impressed you did something they couldn’t.

You may not be an expert woodworker, but the advice here should help you become better. Continue to explore your options with this craft so that you can experience the excitement of creating wood art. Explore the creative possibilities before you.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com