• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

For A Comprehensive Collection Of Tips About Woodworking, Read This

By The Carpenter

Woodworking is not a common skill. But for those inclined to enjoy working with this medium, the rewards are endless. If you are a person that enjoys working with wood, or just have a project in mind, read the advice contained in this article. These tips will help you understand and learn more about woodworking.

Practice some table saw safety. When crosscutting with a table saw, set your cut length with the block clamped to your fence. Do not use your fence directly for avoiding get kicked back by a board directly. You need to clamp the block of wood to your fence before your blade. The board’s end is free of the fence when you cut and after you cut.

Before using any new tool, do your research on it in full. New tools can mean serious injuries for those that use them incorrectly. Even if you’re pretty sure of how to use it, don’t risk it. Study up via the web and books related to the tool in question.

When sanding a piece of lumber, beginning with a coarse sandpaper. Remove the excess dust from the lumber. Then, once the largest scratches are removed, sand again with a smoother sandpaper. Follow this sanding with a tack cloth. Continue using smoother sandpaper until the lumber feels smooth when you run your hand across it.

Before you start any woodworking project, get all of the tools you will need for the project ready. Always remember to bring a calculator and tape measure with you when you go to purchase your wood. Make sure you have any specialty tools you will need for your project available as well.

Before you cut into a piece of wood, you need to inspect it to make sure there are not any pieces of metal in the wood. Screws, nails, staples and other metallic object will not only damage your blades, but also pose a safety hazard. Always inspect the wood before you cut.

You should check the condition of your blade before you start sawing. A blade that has become dull can make it almost impossible to saw as you need to. On a non-power saw, a dull blade can make exact cuts hard to pull off. This can cost money if the piece is cut too short.

If you are going to be doing a big woodworking project on the outside of your home, check to make sure it is within the rules. Your local government may have zoning regulations or even a permit process needed for structures like garages, decks and even storage sheds. Also check with your neighborhood association if there is one.

Learn about using pilot holes. This is pretty simple to do. When driving a screw or hammering a nail into a little piece of wood or getting pretty close to the edge of a piece, it tends to split. Sometimes it’s unavoidable to put a fixing into a place like this. However, drilling a hole through the joint that’s a bit smaller than the fixing can prevent it from splitting.

Never allow someone to watch while you are woodworking without wearing the same gear that you are wearing. Being anywhere near the tools is a hazard, even if they are not using them. Wood or parts of the tool could fly into the air and strike them just as they could you.

You can see that woodworking is a very diverse skill. It takes skill to make items like baseball bats, bookshelves, bowls or a multitude of other wood projects. Don’t feel like you must be greatly talented to work with wood. With the right ideas like this article showed you, you can be creative and successful when working with wood.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com