• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Fine Furniture And How To Make It With Your Woodworking Tools

By The Carpenter

Are you a fan of woodworking? Is it something you have attempted before? Perhaps you already use wood to create beautiful pieces? The tips in this article should help you learn something new. Read on to learn some more about this craft.

Clean your saw’s teeth before cutting lumber. To thoroughly clean your saw blade dip a shop rag into a little acetone and wipe the blade thoroughly. Additionally, using a piece of sandpaper that has a fine grit will remove any sap or gumminess from your skill saw’s cutting blades.

If you will be re-coating an existing finish, be sure that the surface is clean and free of any wax or oils. Then, let it dry completely, and lightly scuff the surface with a 220-grit sandpaper so that the finish you are applying will have something to hold onto.

When sanding a piece of lumber, beginning with a coarse sandpaper. Remove the excess dust from the lumber. Then, once the largest scratches are removed, sand again with a smoother sandpaper. Follow this sanding with a tack cloth. Continue using smoother sandpaper until the lumber feels smooth when you run your hand across it.

If you have your own table saw, you will eventually have to crosscut some wood. This can bring your fingers very close to the saw guard and blade. If the saw kicks back, you could be headed to the hospital. It is best to cut a block of wood to push the wood through the saw with.

When you need accurate measurements in the 3-foot range, use a drafting square. These are relatively cheap and can be found at any art supply store. They are perfectly straight and extremely accurate. They are less cumbersome than a framing square and are also longer. This will become your go-to tool in your woodworking shop.

When staining woods, always test in a hard to see area before moving forward. In fact, if you’ve got a piece of scrap wood, that’s even better. You never know how a type of wood will take to stain, so it’s best to find out in a place that won’t be an issue later on.

If you are going to be doing a big woodworking project on the outside of your home, check to make sure it is within the rules. Your local government may have zoning regulations or even a permit process needed for structures like garages, decks and even storage sheds. Also check with your neighborhood association if there is one.

Learn about using pilot holes. This is pretty simple to do. When driving a screw or hammering a nail into a little piece of wood or getting pretty close to the edge of a piece, it tends to split. Sometimes it’s unavoidable to put a fixing into a place like this. However, drilling a hole through the joint that’s a bit smaller than the fixing can prevent it from splitting.

Avoid becoming obsessed with tape measures. Use story sticks and work up to cutting. Scrap wood cutting is smart and means that you are able to try out a fitting. Planning out your cuts in different ways keeps your mind working.

Save some money and practice your woodworking skills by building essential items for your work space. Build some counters to work on and a work bench. Get creative and you can make your work space even more organized and efficient since you have the ability to organize the area.

It is time for you to pick up your hammer and chisel and start working with wood. Don’t think that this is impossible to get through. Just use the advice you’ve learned here to help you out. It takes determination and time to become a better woodworker, but you can do it. Now you just have to get creative and try something new.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com