• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Do You Need Some Woodworking Advice? Read These Tips.

By The Carpenter

Woodworking is a very unique and interesting craft. There are all kinds of things you can make with wood, both small and large. If you want to know more about honing your craft, continue reading to find out more about how you can get better skills when it comes to woodworking.

For crosscut guides use a stair gauge. Make sure that they are clamped next to the carpenter’s square when you cut. Then use a pencil to mark the notches. Putting them both on the carpenter’s square’s tongue will make an excellent guide for your circular saw.

When sanding a piece of lumber, beginning with a coarse sandpaper. Remove the excess dust from the lumber. Then, once the largest scratches are removed, sand again with a smoother sandpaper. Follow this sanding with a tack cloth. Continue using smoother sandpaper until the lumber feels smooth when you run your hand across it.

Refrain from putting your fingers near your cut. Instead, push the pieces through your saw with a long strip of wood. This helps you keep every finger, which are required for doing future woodworking.

Check out your local library for books on woodworking. You will likely find books that contain tips, special skills or even step-by-step guides that can take you from start to finish on a project. A library can be wonderful source of information that people tend to forget when they are looking for knowledge, so do not let this resource slip your mind.

Every shop that does woodworking needs to contain a stair gauge. Commonly used to scribe stair jacks, it can also be used to attach to your carpenter’s square. That means your square becomes a circular saw guide. If you use the square as a guide, your cuts will be straight every time.

If there is a joint in your work that does not fit together properly, this cannot be fixed with glue. While it may seem like the simple way to fix things, it will only work temporarily. The best thing to do would be to start over and be more careful the next time.

Working with a table saw can be quite dangerous for people that have long hair. If you are one of these people, it would be a good idea for you to tie your hair up while you work. You don’t want any of your hair to get caught in the blades.

Learn how to find the center in a piece of firewood every time. Mount some flat scrap wood to the lathe’s faceplate. Attach an acrylic piece to it using some double-faced tape. Chuck that in your lathe. Turn your acrylic to a disc. Using a 1/16′ bit in your tail stock chuck, drill a hole through that center-point. Scribe some concentric circles on to the disc at 1/2’³ intervals using a skew chisel. Position this center-finder over the end of your stock and adjust it until one of your circles is inscribed completely in a portion of the wood that is solid and usable. Using an awl or nail set, mark your center through the central hole in the disc.

Before you paint your wood project, make sure that you have properly sanded the piece. Start with a coarser grade of sand paper, then gradually change to a finer grade. After sanding, wipe your project with a tacky cloth to pick up residual wood dust. After that, your piece will be ready to be painted.

Now that you’ve read through these tips, you are better equipped to get to some woodworking. It does take time and practice, but it is such a peaceful experience. Woodwork is all about creating something unique, so just let your mistakes and experiences guide you as you practice what you’ve read.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 · mywoodworkingsite.com