• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Check Out These Tips About Woodworking To Gain Comprehensive Knowledge Of The Topic

By The Carpenter

It’s not easy to run a woodworking business. You should know what you’re doing and it will take hard work. Use the tips that work best for your needs. Read other tips. Keep reading, and make sure you use the great advice here.

TIP! Try using a stair gauge as a crosscut guide. Clamp them to your carpenter’s square, and make sure they match your stair jack’s rise and run.

When doing any woodworking project, safety is a big concern. Wear safety equipment and always use tools the correct way. Do not remove any safety guards from tools because they are there for your protection. This will reduce the chances for severe injury.

If you plan to stain a project, apply pre-stain products to your wood. This will help you to get an even finish when you stain. This is because the conditioners allow stains to penetrate evenly.

TIP! Avoid using your fingers as guides while cutting narrow pieces of wood. Use a strip of wood instead to maximize safety.

Consider making your own sanding blocks that can be used again and again. First cut 6 blocks from scrap plywood, one for each grit of sandpaper you like to use. Be certain they measure 2.5 inches across by 4.75 inches long. Use an adhesive spray on the blocks as well as your cork tile square. Apply the wood to the cork and trim the cork with a utility knife. Spray adhesive on a piece of sandpaper and stick that to both cork blocks face down. Lastly, put the sandpaper flush to the cork, labeling all blocks.

Stair gauges can be used as crosscut guides. Clamp these gauges to the carpenter’s square you have and be sure they’re matching up to the stair jack’s run and rise. Be sure to mark the location of the notches. When you combine them on your carpenter’s square’s tongue, they’ll guide your crosscuts for you.

TIP! Your woodworking shop needs a stair gauge. They are typically used for laying out stair jacks, but they can also be used as a clamp for a carpenter’s square.

Stir stains and finishes instead of shaking them to mix. These can settle can must be stirred. However, if you shake it, it may create bubbles and not allow the product to mix well. Make sure you stir properly, until everything is even and smooth.

When you’re working out a budget, you have to think about itemizing the new tools you may have to purchase. You may only think about the wood and overlook the tools themselves. Still, tools can get expensive, so you have to think about them.

TIP! Know what a wood’s characteristics are prior to staining it when you’re working on a project. Paint grade wood is generally of lower quality and stain grade has better grain patterns.

Whenever you plan to cut a narrow piece of wood, don’t use your fingers as a guide! Instead, use a piece of scrap wood to safely push the lumber through your table saw. This helps you keep every finger, which are required for doing future woodworking.

Woodworking requires skill, hard work and dedication. You must stay up to date on industry techniques and practices. Use this information and the suggestions offered to implement it to your situation and become a better woodworker.

Filed Under: Woodworking Tips Tagged With: Blog

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com