• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar

My Woodworking Site

woodworking tips & tricks


  • Home
  • Woodworking 101
  • Woodworking Tips
  • Legal Pages
    • Privacy Policy
    • Terms of Use
  • Contact

Allay Your Worries By Reading This Article Regarding Woodworking

By The Carpenter

Most people don’t know much about the hobby of woodworking. They think it’s just a matter of cutting some wood, slapping it together and calling it a success. The fact is that there is more to it than that, and the tips below will guide you through the process.

Take the time to plan out your woodworking project step-by-step before you even begin. Doing this will help to ensure that you are going to get the results that you are looking for. If you do not plan ahead it is likely that you will make an error that could ruin the entire project.

Become more accurate by using a drafting square. If you need an accurate square that’s about 2″ to 3″, you have limited options. Drywall squares tend to be very inaccurate. With carpenter squares, you have to hook them onto your work piece’s edge. A drafting square can be easily used if you happen to have one lying around. If you don’t, they are pretty cheap to find at art stores. They are incredibly accurate and as useful as a tape measure.

Clean your saw’s teeth before cutting lumber. To thoroughly clean your saw blade dip a shop rag into a little acetone and wipe the blade thoroughly. Additionally, using a piece of sandpaper that has a fine grit will remove any sap or gumminess from your skill saw’s cutting blades.

Try using duct tape to create a level spot. If you’ve used your table saw on a base that’s mobile, you should be able to easily pull it in and out. To really finish it up, find a level spot on your floor. This also helps you saw boards without obstruction. Mark your wheel positions using duct tape that is brightly colored, and then roll the saw to that same flat spot each time you need to saw.

Keep all of your woodworking tools in a safe and dry place. You want to be sure that your tools are not in reach of children, as well as that they will be safe from moisture and other elements that can cause them to degrade at high rate. Follow this rule and your tools will last a long time.

Avoid using your fingers as guides while cutting narrow pieces of wood. Instead, push the pieces through your saw with a long strip of wood. This will ensure that you keep all ten of your fingers, which are all necessary for you to continue working with wood.

Whenever you work with power tools, be sure your clothing is tucked in properly. Any loose clothing or long, dangling hair or jewelry can easily become tangled in the tool, leading to injury or other disaster. Tuck everything in, pull back your hair, take off dangling jewelry and then get down to work.

Working with a table saw can be quite dangerous for people that have long hair. If you are one of these people, it would be a good idea for you to tie your hair up while you work. You don’t want any of your hair to get caught in the blades.

When you find a nice level spot on your workshop floor for your table saw, it can be difficult finding the same spot after you put your saw away. When you do find a level spot, use duct tape on the floor so you know where to position your table saw next time you need it.

As you learn more about woodworking, you’ll find that things become easier. You’ll be able to plan out your projects better, complete them on time and have end results which are impressive. Use this new knowledge to make your hobby the best it has ever been, time and time again.

Filed Under: Woodworking Tips

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

Categories

  • Woodworking 101
  • Woodworking Tips

Featured Posts

Beginners: Essential Fundamentals to Woodworking

Always Place Safety First in Any Woodworking Tasks

Key Health Concerns To Keep In Mind When Woodworking

Differences Between Hardwoods and Softwoods

Common Misconceptions in Woodworking

Popular Tags

1/2 inches applying glue bird feeder Blog carpenter square crosscut guide cutting laminate drafting square dry fit dry fitting dull blade dull blades extension cord extra spring gel stains golf tee grade indicates grade refers grade wood particle board perfect height power sander power tools safety equipment sanding block sanding blocks scrap plywood scrap wood screw holes size nail spray adhesive stair gauge stair gauges stair jacks tain conditioner tile square tin snips utility knife wood shop woodworking business woodworking project woodworking projects woodworking shop woodworking skills workbench height

Copyright © 2021 ยท mywoodworkingsite.com